Motionshop.net, Rio Rancho, NM (2026)

02/14/2025

Motion Control – Half Inch Stroke, and High Force-to-Size Ratio, Are Features of Miniature Voice Coil Servo Motor!

Motion Control – Miniature Voice Coil Motor!

Motion Control – Newly released from Moticont, the miniature GVCM-019-022-02 Linear Voice Coil Servo Motor, is just three-fourths of an inch (19.0 mm) in diameter and features a half inch (12.7 mm) stroke. This very small linear actuator, also referred to as an electric cylinder, features 8.4 ounces (2.3 N) of continuous force and 26.6 ounces (7.4 N) of peak force at a 10 percent duty cycle.

This non-commutated brushless servo motor features: High reliability, high speed, high acceleration/deceleration, and repeatability when used in a servo loop, and zero cogging. The compact housing and coil end combined are just 1.063 in. (27.0 mm) long and in the fully extended position the threaded shaft extends 0.786 in. (19.9 mm) beyond the face of the housing. The end of the shaft has a 2-56 UNC-2A thread 0.156 in. (4.0 mm) long for backlash free connections. Both the housing and coil ends of the actuator have two 4-40 UNC-2B threaded mounting holes on 0.313 (7.9 mm) bolt circles for easy integration into an application.

Non-commutated, these brushless miniature linear servo motors are clean, quiet and an ideal choice for: Haptic feedback and pipetting in medical devices, laser, machining and drilling, work holding and clamping, scanners and laser beam steering and filtering, optical focusing, dynamic vibration absorption, testing, sorting, and assembly. Additionally, they should be considered as low-cost replacements for pneumatic linear actuators.

Please contact Moticont, if a longer stroke or higher force is required for your application.

For additional information contact Sales Team at Moticont, 6901 Woodley Ave, Van Nuys, CA 91406; Toll Free: +1 (888) 785-1804, Tel: +1 (818) 785-1800, [email protected] visit the website at http://www.moticont.com

01/18/2025

Motion Control – Compact Rotary Solenoids Available in OEM Quantities, Can Be Performance Matched To An Application!

Motion Control – Rotary Solenoids

Motion Control – Solenoids – The R-09-150 CCWM Series of Counter Clockwise, Forward Shaft Extension Rotary Solenoids from Magnetic Sensor Systems (MSS), available in OEM quantities, features 18 different winding configurations allowing the user to match torque and duty cycle requirements to an application.

These compact 38.1 mm (1.50 in.) diameter solenoids are just 22.098 (22.1) mm (0.87 in.) long and have two M4X0.7 threaded studs (8-32 studs optional) 7.366 (7.4) mm (0.29 in.) long on a 22.225 (22.2) mm (0.875 in.) bolt circle. The shaft has 40 degrees of counter clockwise rotation, extending (13.0) mm (0.51 in.). The shaft end is serrated for a better grip of the attached load.

The R-09-150 CCWM Series of Rotary Solenoids can be specified with a choice of AWG winding of 21 to 37 gauge. Specifying a different AWG for the windings allows the user to control the performance of a solenoid with respect to duty cycle, current supplied, and torque by controlling the ampere turns.

As an example: Starting torque of a solenoid at 9 w, at 100% duty cycle, is 3.0 oz-in. (0.021 Nm) and starting torque of a solenoid at 90 w, 10% duty cycle is 21 oz-in. (0.15 Nm). When voltage is removed, a built-in return spring returns the shaft to the home position.

The shaft is supported by two high precision radial ball bearings with no axial movement. Low cost, the R-09-150 CCWM Series of Rotary Solenoids feature long life, clean and quiet operation are ideal for: Office machines, security mechanisms (interlocks), medical devices, assembly, sorting, clamping, packaging, shutter actuation, vending, and games. Please consult our Sales Team if another size, higher forces, direction of rotation, or mounting configuration is required.

About Magnetic Sensor Systems – Established in 1983, Magnetic Sensor Systems (MSS) designs and manufactures high quality motion control solenoids, electromagnets, driving electronics and other types of electro-mechanical components for a variety of industries and applications.

Part of Magnetic Sensor Systems’ competitive advantage is its state-of the-art in-house manufacturing facility in North America. Highly controlled processes, committed staff and extensive testing complement their product design strengths. This enables Magnetic Sensor Systems to supply the most demanding clients from specialized small orders to high volume just-in-time deliveries. Magnetic Sensor Systems is an ISO 90001:2015 certified company.

Through wise and aggressive use of their resources and technology, MSS has become recognized as one of the world’s leading solenoid manufactures with a global customer base.

An extensive line of standard products are ready to be shipped immediately from stock, however, when required, their highly trained design engineers, are always available to work with a customer’s design staff to augment or develop a custom product to fit the specific needs of the customer.

For additional information contact the Sales Team at Magnetic Sensor Systems, 6901 Woodley Ave, Van Nuys, CA 91406; Toll Free: +1 (888) 785-9444, Tel: +1 (818) 785-6244, E-Mail [email protected] or visit the website at http://www.magneticsensor systems.com

12/26/2024

Motion Control Products – RVC-1008 Miniature Rotational Voice Coil Stage from Equipment Solutions

Motion Control Products – Miniature Rotational Voice Coil Stage

Motion Control — The RVC-1008 Rotational Voice Coil Stage: Optical element widths up to 20mm; Controllable motion over +/-10 degree optical; Small step response of less than 3msec; Non-contact electro-optic position sensor; Positioning sensitivity of less than 2µrad; Analog and USB control of mirror position; Digital positioning resolution of 6µrad; Fully integrated PID servo controller; Simple USB electrical interface; Extremely compact design.

Equipment Solutions, Inc. (ESI) is a provider of engineering and manufacturing services. ESI specializes in the design and production of automation and instrumentation products including motion control components and sub systems. ESI’s products range from galvanometer amplifiers with an integrated arbitrary waveform generator, to high-resolution displacement sensors, voice coil and stepper motor stages, amplifiers and controllers.

For additional information contact Jeff Knirck at Equipment Solutions,Inc. Mailing Address – PO Box 159, Forestville, CA 95436; Shipping Address 6490 Front Street, Forestville, CA 95436; Tel: 408-245-7162, Fax: 408-245-7160, E-Mail: [email protected] or visit the Website at http://www.equipsolutions.com

10/28/2024

Motion Control – Deep Groove Stainless/Ceramic Hybrid Si3N4 Silicon Nitride Radial Ball Bearings for High Loads Are FDA/USDA/3A-Dairy Compliant!

Motion Control – Hybrid Si3N4 Silicon Nitride Radial Ball Bearings

Deep Groove Hybrid Radial Ball Bearings featuring Si3N4 Silicon Nitride Ceramic balls from LM76 complement their broad range of linear bearings that are FDA/USDA/3A Dairy compliant. These Deep Groove Stainless/Ceramic Hybrid Si3N4 Silicon Nitride Radial Ball Bearings are ideal for the extreme environments experienced in the food, drug, and dairy industries. Capable of high speeds, high radial and axial loads, 24/7 duty cycles, and extreme sanitizing procedures such as high pressure washdown, and caustic foaming agents.

The advantages of Stainless/Ceramic Hybrid Si3N4 Silicon Nitride Ball Bearings are longer life because of lower friction and vibration, lower thermal expansion and heat transmission, therefore, catastrophic failure is all but eliminated. Balls made from Si3N4 Silicon Nitride are smoother than steel balls resulting in lower friction removing the chance of micro-welding or smearing resistance between mating surfaces, and as they will not deform under pressure higher loads are possible with no risk of spalling, and they have an electrical resistivity of 10^14. These deep groove radial bearings are ideal for use in: Food, dairy, and pharmaceutical processing, deep space, under water, assembly and sorting applications, high speed spindles, cleanrooms, motors, and pumps.

Heat and corrosion are two factors that lead to bearing failures. Ceramic Hybrid Si3N4 Silicon Nitride Balls are inert, low thermal and electrical conductors and do not contribute to cross corrosion between bearing components and are unaffected by corrosive agents such as acids and salts. Longer life, higher speeds and loads equals greater through put and lower operating costs.

Deep Groove Stainless/Ceramic Hybrid Si3N4 Silicon Nitride Ball Bearings are available with Nitrile or PTFE shields, with Stainless or Chrome Steel races and with IDs of 3mm to 120 mm.

When others think catalog … … LM76 thinks solution!
To follow the Series from LM76, THE ENGINEERING EDGE! and learn about interesting Outside-of-the-Box solutions developed by LM76 to solve some interesting linear motion problems!

Founded in 1976, LM76 has been a leading designer/manufacturer of motion control linear bearings, slides and linear motion control systems. LM76 is renowned for its industry leading Minuteman PTFE Composite linear bearings. LM76 is a leading supplier of precision linear shafting: RC60, 300 Series Stainless Steel, and ceramic-coated aluminum shafting. LM76 also offers several FDA/USDA compliant linear bearings and slides for the food processing, pharmaceutical, medical, and packaging industries.

For additional information contact Mike Quinn at: LM76, 140 Industrial Dr., E. Longmeadow, MA 01028; Telephone: 413-525-4166, Fax: 413-525-3735 or E-Mail: [email protected] or visit the website at http://www.lm76.com

10/21/2024

Motion Control – Ultra-High Precision, Compact, Low Cost, Optical Positioning System Features Zero Translation from Equipment Solutions!

Motion Control – Linear Focus Actuator
Optical Positioning System – Developed for precision optical positioning applications the LFA-1210 Linear Focus Actuator features a patented zero-translation tangential flexure for high speed travel. The clear aperture, 10 mm (0.394 in.) stroke length and standard 12 mm optics mount (or an optional DIN mount for use on microscopes) make this linear focus actuator ideal for: Optical focusing, scanning, interferometry, surface structure analysis, disk drive testing, autofocus systems, confocal microscopy, biotechnology, and semiconductor test equipment.

A frictionless, closed loop, non-contact sub-micron resolution linear displacement sensor having high bandwidth and low noise assures high responsiveness and ultra precision. Positioning resolution of the LFA-1210 actuator is 150 nm, repeatability is 200 nm (short term) and 50 ppm/1000 hr. (long term) with 2.2 lbs. continuous and 3.5 lbs. peak force.

The corresponding SCA814 Linear Servo Controller is also available from Equipment Solutions. It is a high performance single axis DC motor controller and amplifier that was developed for applications requiring high temporal and spatial servo precision.

motion control - linear focus actuator

Equipment Solutions, Inc. (ESI) is a provider of engineering and manufacturing services. ESI specializes in the design and production of automation and instrumentation products including motion control components and sub systems. ESI’s products range from galvanometer amplifiers with an integrated arbitrary waveform generator, to high-resolution displacement sensors, voice coil and stepper motor stages, amplifiers and controllers.

For additional information contact Jeff Knirck at Equipment Solutions,Inc. Mailing Address – PO Box 159, Forestville, CA 95436; Shipping Address 6490 Front Street, Forestville, CA 95436; Tel: 408-245-7162, Fax: 408-245-7160, E-Mail: [email protected] or visit the Website at http://www.equipsolutions.com

10/18/2024

Motion Control – New Harmonic Drive HPF Series: High-Performance Hollow Shaft Gear Unit

The new Harmonic Drive® HPF Series has quickly become a go-to choice for engineers requiring high-torque solutions in compact spaces. Its precision gearing, reliability, and versatility make it ideal for robotics, automation, and other high-performance applications that require exact motion control.

Key Applications:
The HPF series has already seen widespread adoption across several industries. In robotics, it is used in robotic arms and precision movement systems, where space-saving designs and torque output are critical. The HPF series is also ideal for medical devices, particularly in robotic surgery and diagnostic machines, where high accuracy is essential.

Its low backlash and integrated cross-roller bearing make it especially suited for industrial automation, enhancing productivity in tasks such as pick-and-place operations and precision manufacturing. Additionally, its durability and compact design make it a perfect fit for aerospace systems, where both size and precision are often limiting factors

Standout Features:
Ultra-Compact Design: The HPF series provides high torque with a minimal footprint, making it ideal for applications where space is at a premium.
High Torque Density: Delivers up to three times the rated torque for stronger performance in smaller sizes, suitable for various demanding applications.
Low Backlash: Provides precise, smooth motion control, essential for tasks requiring high accuracy.
Built-in Cross Roller Bearing: Enhances load capacity and simplifies integration, contributing to longer system life and greater efficiency.

For more information, visit https://electromate.harmonicdrivegearhead.com/products/harmonic-planetary-gear-units/hpf

About Electromate:
Electromate specializes in robotic, mechatronic, and motion control solutions. We focus on high-performance and precision applications for the industrial automation sector.

Electromate’s Core Purpose is to help Manufacturers build better machines using differentiated automation technology.

They specialize in Robotic and Mechatronic Solutions for the Industrial Automation marketplace. Respected by customers as a premiere source for High Performance Automation and Motion Control Components & Systems, Electromate® specializes in AC & DC Servo and Stepper Motors & Drives, Motion & Automation Controllers, Positioning Systems & Actuators, Feedback Devices, Gearing Products and HMI’s & Operator Displays, all supported via extensive product selection, just-in-time delivery, dedicated customer service and technical engineering support.
More on Electromate can be found at

Website: http://www.electromate.com

07/02/2024

Motion Control – Electric Cylinder from Moticont Has Zero Cogging and High Throughput!
Motion Control – Electric Cylinder Has Ze

Van Nuys, CA — Motion Control – Moticont has added another non-commutated linear actuator to its DDLM series of low cost actuators.

The 0.125 in. (3.2 mm) diameter shaft has an internal thread on each end, a total of length of 4.960 in (126.0 mm), and extends 1.585 in. (40.3 mm) past the mounting end of the actuator. The shaft extends thru the 3/8-32 UNF x 0.250 (6.4 mm) long threaded studs at each end of the housing which can be used for mounting the DDL-019-070-01 linear actuator. Long life plain linear bearings support the internal shaft at both end of the actuator.

This new DDLM-019-070-01 Linear Actuator can develop 10.1 oz (2.8 N) of continuous force and 32.1 oz (8.9 N) of peak force at 10% duty cycle. Having a stroke of 0.960 in. (24.4 mm), this clean, fully enclosed linear actuator, also referred to as an electric cylinder is ideal for use in critical medical applications. Measuring just 0.750 in. (19.1 mm) in. diameter with a housing length of 2.750 in. (44.5 mm) long, this zero cogging, bi-directional actuator is easily integrated into new and existing applications. Each end of the shaft is threaded for direct coupling of the actuator to the load resulting in zero backlash allowing for smooth, high speed positioning, and high acceleration/deceleration resulting in greater throughput.

Highly controllable force, stroke length and speed, low noise, and maintenance free, the DDLM-019-070-01 can be used with a position sensor and controller for the high repeatability and accuracy of a closed loop application.

For assistance in selecting the best linear actuator for a specific application such as: Life support in ventilators or respirators, reagent dispensing, sampling, sorting, or assembly, contact the Moticont sales team.

The DDLM-019-070-01 actuator is just one of a wide range of actuators available from Moticont. For assistance in selecting the best linear actuator for a specific application such as: Life support, reagent dispensing, sampling, sorting, assembly, valve actuation, or positioning contact the Moticont sales team.

About Moticont – Moticont is a manufacturer of motion control products. Their product line includes voice coil motors, three phase brushless motors and positioning stages and slides.

Moticont is committed to exceeding their customers’ quality expectations and industry standards throughout the design, manufacturing, service and technical support phases. Their modern manufacturing facility, highly controlled processes, committed staff, and extensive testing complement their product design strengths. This enables them to supply their clients with specialized small orders to high volume just-in-time deliveries.

They offer an extensive line of standard products ready to be shipped immediately from stock, and when standard products are not quite right for an application, highly trained design engineers are always available to develop custom motion control products to fit the specific needs or our customers.

For additional information contact Sales Team at Moticont, 6901 Woodley Ave, Van Nuys, CA 91406; Toll Free: +1 (888) 785-1804, Tel: +1 (818) 785-1800, [email protected] visit the website at http://www.moticont.com

06/22/2024

Motion Control – More Advantages With Temposonics R-Series V Profinet

Motion Control – Linear Sensors

Motion Control – Temposonics, the industry leader in magnetostrictive linear sensor technology, has announced a new generation of sensors focused on Industry 4.0, which features advanced machine monitoring and predictive maintenance capabilities to enhance industrial productivity.

The R-Series V PROFINET now transmits additional sensor status information, such as internal temperature, total operating hours, and distance traveled by magnets, directly to the controller via the PROFINET protocol. This allows for improved predictive maintenance and machine condition monitoring.

Updates include the encoder profile version V4.2, making the R-Series V PROFINET the first linear position sensor certified for this version. The MTS profile and corresponding description file have also been certified by PNO. The Temposonics profile enables easy parameter setting and simultaneous monitoring of switching points with position and velocity output, synchronized with the controller’s clock.

Available in rod- and profile-style, the R-Series V transducers have a 37% smaller housing, allowing for more compact application designs. They are more robust and reliable, with an extended operating temperature range of -40° to +85°C, increased shock resistance to 150 g, and vibration resistance to 30 g. The larger voltage supply range facilitates integration into harsher environments while maintaining precise measurements up to 0.5 µm.

Backward compatible with previous generations, the R-Series V combines proven performance and quality with new, intelligent features, delivering familiar reliability with enhanced functionality.

For more information, visit the R-Series V Profinet Transducer brochure.
https://www.electromate.com/media/assets/catalog-library/pdfs/mts-sensors/mts_r-series_v_rp_profinet_rt_and_irt.pdf

About Electromate:
Electromate specializes in robotic, mechatronic, and motion control solutions. We focus on high-performance and precision applications for the industrial automation sector.

Electromate’s Core Purpose is to help Manufacturers build better machines using differentiated automation technology.

They specialize in Robotic and Mechatronic Solutions for the Industrial Automation marketplace. Respected by customers as a premiere source for High Performance Automation and Motion Control Components & Systems, Electromate® specializes in AC & DC Servo and Stepper Motors & Drives, Motion & Automation Controllers, Positioning Systems & Actuators, Feedback Devices, Gearing Products and HMI’s & Operator Displays, all supported via extensive product selection, just-in-time delivery, dedicated customer service and technical engineering support.

More on Electromate can be found at
Website: http://www.electromate.com

LinkedIn: https://www.linkedin.com/company-beta/209277/

Twitter: https://twitter.com/Electromate

Facebook: https://www.facebook.com/electromateindustrial/

Blog: https://electromate.wordpress.com/

06/11/2024

Motion Control – Rotational Voice Coil Stage quickly and repeatably steers an optical beam with a diameter of up to 25 millimeters over 90° with 25 microradians of resolution!

Motion Control – Rotational Voice Coil Stage

Quickly and repeatably steer an optical beam with a diameter of up to 25 millimeters over 90° with 25 microradians of resolution!

RVC-9025 Rotational Voice Coil Stage: Up to 25mm wide mirror; Controllable positioning over +/-45 degree optical; 5 arcsec (25 microradians) optical position repeatability; 1 degree optical step-and-settle in less than 5ms; Fully integrated servo controller; USB 2.0 and auxiliary user electrical interfaces; X 58 x 28 x 21 millimeters, 30 grams

Forestville, CA – The RVC-9025 Rotational Voice Coil Stage provides a means to quickly and accurately set an angular position. The frequency is factory adjusted to customer specifications during the manufacturing process. Amplitude of the resonating mirror can be adjusted through either an analog input voltage or the USB interface.

An optional high-resolution position feedback sensor can be monitored by an analog output signal on the User Connector.

The RS-25 Resonant Scanner can also be configured with a high-resolution 16-bit Analog to Digital Converter to quickly sample and report the mirror position at any moment if the position sensor is included.

The RVC-9025 Rotational Voice Coil Stage provides a means to quickly and repeatably steer an optical beam with a diameter of up to 25 millimeters over 90° with 25 microradians of resolution. The RS-25 Resonant Scanner is designed and optimized for applications that typically require a means to scan an optical beam. Using various patent pending features the RS-25 Resonant Scanner can run 24/7 forever without compromise. At the heart of this product is a pair of carefully designed flexures that mimic the spring in a classical spring-mass harmonic motion system. The mirror or other load acts as the mass and together a natural resonating frequency is borne that provides unparalleled performance and reliability. A small motor is carefully coupled to the system to makeup for small system losses that would otherwise dampen the oscillation.

The Mirror: The mirror is an integral part of the RVC-9025 and is usually specified at time of order. The mirror and its associated inertia will largely predict the overall step and settle time of the actuator. With that in mind the user should careful consider parameters surrounding the mirror including its shape and flatness. The mirror should be no wider than absolutely necessary and sufficiently long to accommodate the beam elongation as a consequence of the tilting process. Mirror flatness will largely dictate its thickness and overall inertia. In special cases, mirror thickness and its affects on inertia can be managed using costlier materials such as beryllium that have a higher specific stiffness. As the mirror thickness grows, its front surface will proportionally move further off the rotational axis which in some cases can be undesirable. Other parameters including coating and scratch/dig need to be included to fully describe the mirror. While a mirror is probably the most common payload other customer supplied or specified loads can be used such as gratings.

Position Sensor: The RVC-9025 is able to position its mirror with a resolution of 25 micro-radians in a large part because of the high-resolution sensor it uses. The analog nature of its non-contact sensor also makes it noise limited by adjusting its bandwidth. Careful control and optimization of the sensor signal permits the servo to operate at a higher bandwidth and thereby having a higher stiffness and exceptionally low positioning wander or hysteresis.

Voice Coil Motor: The RVC-9025 includes a high efficiency voice coil motor–sometimes referred to as a single phase DC motor. The motor coil is directly coupled to the mirror support beam and position sensor. That tight and rigid coupling of the load, actuator and sensor assures exceptional position repeatability and step-and-settle times. The high efficiency of the motor coil yields a small and light-weight coil that adds little of the overall motion inertia.

Integrated Electronics: The RVC-9025 includes a highly miniaturized servo amplifier and controller. The mirror position can be controlled through either the USB and its 16-bit DAC or an analog input signal. At the same time mirror position can be monitored from and analog output or the USB and an optional 16-bit ADC. The auxiliary input header also provides a means to enable the amplifier and monitor it for faults. Thereby supporting a configuration for a deeply embedded and autonomous device.

Equipment Solutions, Inc. (ESI) is a provider of engineering and manufacturing services. ESI specializes in the design and production of automation and instrumentation products including motion control components and sub systems. ESI’s products range from galvanometer amplifiers with an integrated arbitrary waveform generator, to high-resolution displacement sensors, voice coil and stepper motor stages, amplifiers and controllers.

For additional information contact Jeff Knirck at Equipment Solutions,Inc. Mailing Address – PO Box 159, Forestville, CA 95436; Shipping Address 6490 Front Street, Forestville, CA 95436; Tel: 408-245-7162, Fax: 408-245-7160, E-Mail: [email protected] or visit the Website at http://www.equipsolutions.com

06/01/2024

Motion Control – FDA/USDA and 3A-Dairy Compliance Brochure features Linear Motion Components from LM76!

Motion Control – FDA/USDA/3A-Dairy Compliance Brochure

E. Longmeadow, MA — Motion Control Components – Linear Motion – Food processing and beverage plants’ wash down areas are unique environments that undergo harsh treatment from high pressure washers, steam, and a multitude of caustic chemicals used in the cleaning and sanitizing production equipment.

OEMs and maintenance departments need to select components that will not trap contaminating debris and can be thoroughly evacuated following Sanitation Standard Operating Procedures (SSOPs). SSOPs are detailed schedules and procedures specifying what to clean, how to clean, how often to clean, and the record keeping used for monitoring.

A helpful component selection guide from LM76, “Linear Bearings, 6 Simple Steps – FDA Compliance, Wash Down Compliance,” details the linear motion components available from LM76 that are FDA/UDSA/3A-Dairy compliant. Included are: Foodstream electrodeless nickel plated pillow blocks, PTFE lined stainless steel bearings, ceramic coated linear bearings, self-aligning corrosion resistant linear ball bearings, and Thomson® Super SmartTM corrosion resistant, self-aligning, high load linear ball bearings. Shafting to compliment the type of bearing selected includes: Class L Stainless 303/304/316, 440C case hardened stainless, Rc 60 case hardened steel with an Armoloy coating and also Rc78 Class L for enhanced hardness and wear resistance. End blocks and shaft supports that have a ceramic or electrodeless nickel coating are also available, as well as new ETX Scraper Seals that prevents intrusion of contaminates adding another line of defense.

LM76 also designs and custom builds linear slides from Stainless Steel and other FDA wash down compliant materials

Shafting options include: Solid and hollow Class L RC60, 300 series stainless steel in lengths to 12 feet. FDA/USDA/3A-Dairy compliant, shafting features: Excellent corrosion and chemical resistance, custom machining to print, pre-drilling and assembly.

To Request the FDA/USDA/3A-Dairy Compliance Brochure from LM76 CLICK HERE -https://www.lm76.com/6%20Simple%20Steps%20HBK.pdf

To follow the NEW Series from LM76, THE ENGINEERING EDGE! and learn about interesting Outside-of-the-Box solutions developed by LM76 to solve some interesting linear motion problems! CLICK HERE - https://lm76blogger.com/the-engineering-edge

About LM76

Founded in 1976, LM76 has been a leading designer/manufacturer of linear bearings, slides and linear motion systems. LM76 is renowned for its industry leading Minuteman PTFE Composite linear bearings. LM76 is a leading supplier of precision linear shafting: RC60, 300 Series Stainless Steel, and ceramic-coated aluminum shafting. LM76 also offers several FDA/USDA compliant linear bearings and slides for the food processing, pharmaceutical, medical, and packaging industries.

For additional information contact Mike Quinn at: LM76, 140 Industrial Dr., E. Longmeadow, MA 01028; Telephone: 413-525-4166, Fax: 413-525-3735 or E-Mail: [email protected] or visit the website at http://www.lm76.com

05/20/2024

Motion Control – Select from the S-70-300H Series of 3 Inch Dia. Push Type Solenoids to Meet the High Force Requirements of an Application!

Motion Control – Solenoids – The S-70-300H Series of high force Push Type Tubular Solenoids has been released by Magnetic Sensor Systems (MSS). Ideal for strokes of up to 4.00 inches, this series of solenoids features 18 different solenoids to select from based on the Force, Voltage, Duty Cycle, and Stroke requirement of the user. MSS Solenoids coils typically utilize Class “F” 23 to 40 AWG (American Wire Gauge) windings with Class “A” lead wire insulation for better protection of the solenoid during longer duty cycles.

The S-70-300H Series of solenoids feature a 3.000 in. diameter x 7.00 in. long housing and a 1.75-12 UN A thread for mounting.

The thrust pin has a diameter of 0.250 in. and extends 4.5 in. beyond the threaded mounting end when energized while the low residual magnetism plunger at the opposite end extends 1.19 in. The non-captive plunger features an anti-bottoming washer, plain bearings, and PTFE coating all helping to extend the life of the solenoids.

These clean, high efficiency, low cost, tubular solenoids can create (voltage dependent) 66 lbs. of force continuously and up to 95 lbs. of force at a 10% duty cycle near the end of stroke at maximum thrust pin extension. They are an ideal choice for: Clamping, packaging, assembly, valve control, farm machinery, disconnects, transmission shifting, fire suppression systems, cabinet locks, door controls, and sorting equipment.

For additional information contact the Sales Team at Magnetic Sensor Systems, 6901 Woodley Ave, Van Nuys, CA 91406; Toll Free: +1 (888) 785-9444, Tel: +1 (818) 785-6244, E-Mail [email protected] or visit the website at http://www.magneticsensor systems.com

Motionshop.net

02/14/2025

01/18/2025

12/26/2024

10/28/2024

10/21/2024

10/18/2024

07/02/2024

06/22/2024

06/11/2024

06/01/2024

05/20/2024

Address

Telephone

Website

Alerts

Contact The Business

Shortcuts

Share

Category